Show basket (0 Article) My accountShow saved listTo checkout

FlexFoam-iT!™ 6 Pillow Soft

These foams are very soft and are used for padding/cushion, specialty bed, and orthopedic pillow material applications. Cured foam has very good physical and rebound properties.

Flex Foam it 6 Pillow soft safety

- Read the safety information label. Click on the image

- Lea la etiqueta de información de seguridad. Haga clic en la imagen

- Lesen Sie das Sicherheitsinformationsetikett. Klicken Sie auf das Bild.

- Lisez les informations de sécurité cliquez sur l'image

- Lees het veiligheidsinformatie label. Klik op de afbeelding.

Flex Foam it 6 Pillow soft

Instructions

Preparation - Store and use at room temperature (73°F/23°C). Use in a low humidity environment (below 50% RH). Mixing containers should have straight sides and a flat bottom. Mixing sticks should be flat and stiff with defined edges for scraping the sides and bottom of your mixing container. Good ventilation (room size) is essential. This product has a limited shelf life and should be used as soon as possible. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

Applying Release Agent - Urethane foams are adhesive and will stick / bond to many surfaces. We recommend Ease Release 2831 to release urethane foam from most surfaces. If the release application is particularly difficult (example; releasing urethane foam from urethane rubber), we recommend an application of Universal Mold Release followed by an application of Ease Release 2831.

WARNING: Do not use Universal Mold Release by itself, or any other silicone based release agents. This will collapse the foam.

IMPORTANT: To ensure thorough coverage, lightly brush the release agent with a soft brush over all surfaces. Let the release agent dry for 30 minutes.

IMPORTANT: Shelf life of product is reduced after opening. Remaining product should be used as soon as possible. Immediately replacing the lids on both containers after dispensing product will help prolong the shelf life of the unused product. XTEND-IT™ Dry Gas Blanket (available from Smooth-On) will significantly prolong the shelf life of unused liquid urethane products.

Pre-mix Parts A & B– Stir or shake both Part A & Part B thoroughly before dispensing.

Measuring – Stop! Know the mix ratio of the foam product you are using. Some are by weight and some are by volume. Dispense the correct amounts of Part A and Part B into a large mixing container.

For Best Results - Pre-Mix Part B after measuring out material – although not necessary, pre-mixing Part B using a drill and mechanical mixer (such as a turbine mixer available from Smooth-On) after measuring out and before combining with Part A will yield best results.

For Best Results - Use a Mechanical Mixer – Mix for 30 seconds and pour into mold or form.

Mixing by Hand – Stir quickly and deliberately for 30 seconds. Make sure that you aggressively scrape the sides and bottom of your mixing container several times. Pour into mold or form.

Be careful not to splash low-viscosity liquid out of container. Remember, these materials cure quickly. Do not delay between mixing and pouring.

Pouring & Curing - For best results, pour your mixture in a single spot at the lowest point of the containment field and let the mixture seek its level. Allow space in the containment field for the foam to grow as it expands to its ultimate volume. Allow foam to cure for at least 30 minutes before handling.

Mass Concentration / Mold Configuration – Pouring large amounts at a time in certain mold configurations (i.e. cylinder) could cause excess heat to be generated and result in splitting (fissures). Step pouring in layers may resolve this problem.

Improving Surface Finish & Minimizing Voids With Back Pressure - Capping the mold cavity opening with a board that has predrilled holes will improve surface finish for some foams. For more information, watch the video at smooth-on.com/backpressure

Is Your Foam Collapsing? - This is a common phenomenon associated with cold temperatures, inadequate mixing or both. Environment or material too cold? Warm it up. Inadequate mixing? You must thoroughly pre-mix both parts A and B. After combining A and B, mix thoroughly. If using a mechanical mixer, mix for 30 seconds. When hand mixing, mix quickly and aggressively, almost whipping the material.

www.formx.biz

- pricing ex VAT
- invoicing ex VAT
- widest product range
- volume discounts

VAT- and Chamber of Commerce registration required.

Orders shipped within the Netherlands will be subject to an additional VAT charge.

our standard discounts

€15.- discount on all orders above net €250.-

Additional discounts will be applied with increasing order volume

from €500,- till €1000,-minus 2%
from €1000,- till €1500,- minus 3%
from €1500,- till €2000,- minus 4%
from €2000,- till €2500,- minus 5%
from €2500,- onward - minus 6%

Make your business more profitable

Do you spend many xxK€ in our webshop? We can help you with a personalized account to make your business more profittable. Contact us at info@formx.nl

(only available through this webshop)

Navigate

BUY SMOOTH-ON AT FORMX

SMOOTH-ON is one of the worlds leading manufacturers of 3D modeling materials for mold-making, casting and special effects.

FormX is a main distributor of SMOOTH-ON in Europe with a wide range of products always on stock. FormX puts great emphasis on customer service and supplies many satisfied clients throughout Europe.

Be a happy client - don't just buy anything, anywhere - buy SMOOTH-ON AT FORMX !

- BEST PRODUCT
- BEST PRICE
- BEST SERVICE

Optional Login



FACEBOOK

FormX Newsletter About us Contact Shipping Applications FormX Academy Terms of Sales Impressum